KODAK EASYSHARE MINI Camera / M200 — Extended user guide

Camera does not turn on

• Make sure the battery is charged and installed correctly (Loading the KLIC-7006 battery). Charge the Li-ion battery whenever necessary.

Camera does not turn off

Camera buttons and controls do not function

LCD is too dark.

• Adjust the LCD Brightness setting ( ).

Pictures remaining number does not decrease after taking a picture

• Continue taking pictures. The camera is operating normally.

(The camera estimates the number of pictures remaining after each picture is taken, based on picture size and content.)

Flash does not fire

• Check the flash setting, and change as needed (Using the flash).

  NOTE:

  The flash does not fire in all modes.

  
  

Memory card is almost or entirely full

• Transfer the pictures to the computer (Transferring, printing pictures).

• Delete pictures from the card (Deleting pictures/videos) or insert a new card.

Memory card not recognized or camera freezes with card

• Card may be corrupted. Format the card in the camera ( ).

• Use another memory card. Only SD or SDHC Cards are supported.

Battery life is short

• Make sure the correct battery type is installed (Battery replacement, battery life).

• Wipe the battery's contacts with a clean, dry cloth before inserting it in the camera.

• Insert a new/charged battery (Loading the KLIC-7006 battery). Charge the Li-ion battery whenever necessary.

• Limit the time you review pictures/videos on the camera LCD.

• Purchase a spare battery at www.kodak.com/go/accessories.

You cannot take a picture

• Turn the camera off, then on again.

• Depress the Shutter button all the way (Taking pictures).

• Insert a new/charged battery (Loading the KLIC-7006 battery). Charge the Li-ion battery whenever necessary.

• Memory is full. Transfer pictures to the computer (Transferring, printing pictures), delete pictures (Deleting pictures/videos), or insert another card.

Cannot find the desired picture/video

• To view pictures on a card or in internal memory, Reviewing pictures/videos.

Slide Show does not run on an external display device

• Adjust the camera Video Out setting to NTSC or PAL ( ).

• Make sure the external device settings are correct. (See the device's user guide.)

Computer does not communicate with the camera

• Turn off the camera, then turn it back on.

• Make sure the battery is charged and installed correctly (Loading the KLIC-7006 battery).

• Make sure the KODAK Camera USB Cable, Micro B / 5-Pin is connected to the camera and the computer (Transferring pictures to your computer). Then turn on the camera.

• See KODAK Software Help at www.kodak.com/go/camerasw.

Cannot print to a PICTBRIDGE Printer

• In the Setup menu, change the Computer Connection setting to Other Application ( ).

Picture is not clear

• To automatically set exposure and focus, press the Shutter button halfway. When the framing marks turn green, press the Shutter button completely down to take the picture.

• Clean the lens (Care and maintenance).

• Make sure the camera is not in Macro mode if you are more than 27.6 in. (70 cm) from your subject ( ).

• Place the camera on a flat, steady surface or use a tripod (especially in high-zoom settings or in low light).

• Use a larger picture size ( ).

• If you're manually adjusting the ISO speed, realize that high ISO setting may cause grainy pictures ( ).

Picture is too dark

• Reposition the camera for more available light.

• Use Fill flash (Using the flash) in Program mode, Backlight in SCN mode, or change your position so light is not behind the subject.

• Move so that the distance between you and the subject is within the effective flash range. (See Specifications.)

• To automatically set exposure and focus, press the Shutter button halfway. When the framing marks turn green, press the Shutter button completely down to take the picture.

• In Program mode, increase the Exposure Compensation ( ).

Picture is too light

• Reposition the camera to reduce the amount of available light.

• Turn the flash off (Using the flash).

• Move so that the distance between you and the subject is within the effective flash range. (See Specifications.)

• To automatically set exposure and focus, press the Shutter button halfway. When the framing marks turn green, press the Shutter button completely down to take the picture.

• In Program mode, decrease the Exposure Compensation ( ).