KODAK HERO 3.1 All-in-One Printer — Extended User Guide


Table of Contents > Copying > Copying a photo

7 Copying

Copying a photo

You can copy a photo using the default settings, or you can adjust the quantity, size, quality, and brightness of your copies.

Using the default settings to copy a photo

The default settings are either the factory default settings (see Resetting factory defaults), or defaults that you have set on the printer (see ).

To copy a photo using the current default settings:

  1. Load photo paper into the printer (see Loading photo paper ).

  2. Lift the scanner lid, and place the photo face down in the right-front corner of the scanner glass.



  3. Close the lid.

  4. Press Home.

  5. Press to select Copy Photo.

  6. Press Start to begin copying.

Adjusting the settings and copying a photo

To copy a photo using settings other than the default settings:

  1. Lift the scanner lid, and place the photo face down in the right-front corner of the scanner glass.



  2. Close the lid.

  3. Press Home.

  4. Press to select Copy Photo, then press OK.

  5. Press to select an option, then press or to change the setting.

    Copy Photo Option Setting Description

    Quantity

    1 (default) to 99

    The number of copies that print.

    Color

    Color (default)

    Prints full color.

    Black & White

    Prints black and white (grayscale).

    Copy Size

    2 x 3

    3.5 x 5

    4 x 6 (default)

    4 x 7

    4 x 8

    5 x 7

    4 x 12

    8 x 10

    8.5 x 11 or A4

    The printer detects the size of the original on the scanner glass and the size of the paper in the paper input tray, and automatically reduces or enlarges the original so that the copy fits on the paper.

    Plain Paper Quality

    Normal (default)

    Good quality output; prints faster than Best.

    Best

    The highest quality, but the slowest print speed.

    Draft

    The fastest print speed, but the lowest quality.

    Photo Paper Quality

    Auto. (default)

    The printer detects photo paper in the paper input tray and sets Best quality automatically.

    Brightness

    Normal (default) - 3 to +3

    Lightens or darkens the copy. Normal is no change from the original; - 3 is the darkest; +3 is the lightest.

    Preview

    No (default) Yes

    To see a preview of the photo on the LCD, select Yes.

    Save as Defaults

    No / Yes

    To save the settings as the new default, press OK. With Yes selected, press OK.

  6. When you have finished changing settings, press Start to begin copying.

Changing the number of copies of a photo

To change the number of copies:

  1. Lift the scanner lid, and place the photo face down in the right-front corner of the scanner glass.



  2. Close the lid.

  3. Press Home.

  4. Press to select Copy Photo, then press OK.

  5. Make sure Quantity is selected.

  6. Press or to select a number.

  7. Press Start to begin copying.


Enlarging or reducing a photo

To enlarge or reduce the size of the copy:

  1. Lift the scanner lid, and place the photo face down in the right-front corner of the scanner glass.



  2. Close the lid.

  3. Press Home.

  4. Press to select Copy Photo, then press OK.

  5. Press to select Copy Size.

    NOTE: Make sure that the paper loaded in the paper input tray is at least as wide as the Copy Size selected, or you will get a wrong paper size error. Also, if the loaded paper is not as long as the Copy Size selected, the output picture will be cut off without any warning.

  6. Press or to select the copy size.

  7. Press Start to begin copying.

Darkening or lightening a photo

To darken or lighten the copy:

  1. Lift the scanner lid, and place the photo face down in the right-front corner of the scanner glass.



  2. Close the lid.

  3. Press Home.

  4. Press to select Copy Photo, then press OK.

  5. Press to select Brightness.

  6. Press to select a number below zero for a darker copy, or press to select a number above zero for a lighter copy.

  7. Press Start to begin copying .



Previous Next