Kodak EasyShare G600 printer dock — User's guide
Table of Contents > Troubleshooting > Printer-dock-status lights
9 Troubleshooting
Printer-dock-status lights
Power button/light | ||||
---|---|---|---|---|
Light status | Cause | Action/solution | ||
Light glows green |
Printer dock is turned on. |
None required. |
||
Light is off |
Printer dock is turned off. |
|
||
|
Color-cartridge light | ||||
---|---|---|---|---|
Light status | Cause | Action/solution | ||
|
||||
Light is off |
Cartridge properly installed and working normally. |
None required. |
||
Light glows amber
|
Cartridge nearly depleted. |
None required. |
||
|
|
|||
Light glows red |
Cartridge depleted or uninstalled. |
Install a new cartridge (Loading the paper and cartridge), then press . |
||
Cartridge incorrectly seated. |
Remove and re-install the cartridge (Loading the paper and cartridge), then press . |
Paper light | ||||
---|---|---|---|---|
Light status | Cause | Action/solution | ||
|
||||
Light is off |
Paper tray properly installed with ample supply of paper. |
None required. |
||
Light glows red
|
Paper jam. |
Clear the jam (Printing problems), then press . |
||
Printing stopped during mid-print; damaged paper. |
Remove loose paper. Check the paper supply. Reload with new paper, if necessary, then press . |
|||
Paper tray empty. |
Load paper (Loading the paper and cartridge), then press . |
|||
Paper tray not installed or improperly installed. |
Remove the paper tray, check that paper is properly loaded, and re-install tray (Removing the paper-tray). Press to resume printing. |
|||
Paper did not feed; sheets stuck together (Printing problems). |
Check the paper supply. Reload with new paper, if necessary, then press .
|
|||
Paper-feed rollers are dirty. |
Clean the paper-feed rollers (Cleaning the paper-feed rollers). |
Camera battery button/light | ||
---|---|---|
Light status | Cause | Action/solution |
Light is off
|
Camera not properly seated on connector. |
Reseat the camera on the printer dock (Docking the camera). |
Unrecognized battery type installed, or camera does not support charging. |
Install a Kodak Ni-MH rechargeable digital camera battery or Kodak Li-Ion rechargeable digital camera battery. See your camera user's guide for battery compatibility and other charging options. |
|
AC power cord not connected. |
Connect the AC power cord (Connecting the power). |
|
Light glows green
|
Camera just placed on printer dock. |
None; dock is checking the charge status of the battery. |
Battery fully charged. |
None required. |
|
Light blinks green
|
Battery charging. |
Leave the camera on the dock to continue charging or to maintain charge. |
Light glows amber
|
Battery not properly installed. |
Re-install the battery. |
Battery or connector pin damaged. |
Check for damage. |
|
Camera and battery exposed to extreme temperatures. |
Slowly return the camera and battery to room temperature. |
|
Battery exhausted. |
Refresh the battery (Refreshing the Kodak Ni-MH rechargeable camera battery). |
|
Light blinks amber
|
The Ni-MH battery pack refresh cycle in progress: discharging (light turns off as discharging progresses). |
Leave the camera on the dock to continue refresh cycle (Refreshing the Kodak Ni-MH rechargeable camera battery). |
Print button/light | ||
---|---|---|
Light status | Cause | Action/solution |
Light glows green |
Printer dock ready for printing. |
None required. |
Light blinks green |
Printer dock printing. |
|
Light is off |
No pictures in the camera or on the memory card. |
None required. To enable Print:
|
|
||
Camera not properly seated on the connector. |
Reseat the camera on the printer dock (Docking the camera). |
|
Camera transferring pictures to the computer; established active connection to the computer. |
None required. |
|
PictBridge compatible device connected. |
None required. The Print button is disabled; print command is controlled from the PictBridge compatible device. To print from another source, unplug the PictBridge compatible device. |
Transfer button/light | ||
---|---|---|
Light status | Cause | Action/solution |
Light glows green |
Printer dock ready for transferring pictures. |
None required. |
Light blinks green |
Pictures transferred to the computer. |
None required. After transferring pictures, the transfer light continues to blink green until either the camera is removed, the Transfer button is pressed again, or the connection is no longer available. |
Light is off |
No pictures in camera or on memory card. |
None required. To enable Transfer:
|
Camera not docked. |
||
Printer dock not connected to computer. |
||
Camera not properly seated on connector. |
Reseat the camera on the printer dock (Docking the camera). |
|
Computer off. |
Turn on the computer. |
Printer battery charging status | ||||
---|---|---|---|---|
Light status | Cause | Action/solution | ||
|
||||
Light blinks amber |
Printer battery power nearly depleted. |
Printer battery able to provide power for only a limited number of prints. Charge the printer battery (see Battery charging). |
||
Light glows amber |
Printer battery less than fully charged. |
Printer battery working normally. |
||
Light blinks green |
Battery charging. |
None required. |
||
Light glows green |
Battery fully charged. |
None required. |
||
Light blinks red |
Battery error. |
Attach a new printer battery (see Attaching the printer battery (optional)). |
||
Light glows red |
Battery needs charging. |
Charge the printer battery (Battery charging). |
Still having problems?
Visit www.kodak.com/go/support, or see Getting help, or contact your camera manufacturer.
Previous Next